T54

Surface planer T54

A surface planer which is a perfect fit for your workshop.

The T54 surface planer was mainly developed to accomplish two tasks – (a) to dress workpieces perfectly and (b) to provide these workpieces with angular edges quickly and safely. This is because you only arrive at the perfect end result with perfect preparation. The easy-running guided surfacing fence with integrated auxiliary fence enables quick and precise working. The ball-bearing guided jointing fence runs smoothly and without tilting on tempered raceways – as precisely for many years to come as it does on the very first day. Chamfers can also be planed in a flash, because any angle between 90° and 45° can be set quickly with the user-friendly one hand operation.
More comfort and a better overview
Integrated auxiliary fence
Intelligent technology – TERSA centrifugal clamping
Modern SUVA bridge guard

Experience the T54!

Operation

The operation of the T54 is as simple as it is effective. Irrespective of whether you set the depth of cut or switch the machine on or off, everything is in one place and easily accessible. You also reach the hollow / pointed joint adjustment from here, the scale shows you the setting.

TERSA solid steel cutter block

The TERSA solid steel cutter block Z2 on the T54 offers many practical advantages: The high running smoothness in the precision bearings and the exact positioning of the form-locked reversible blades result in an extremely accurate cutting circle – and thus the best conditions for cleanly planed surfaces. The TERSA reversible blades are available in four different qualities, i.e. for all tasks, and the cutter block can also be supplied as a Z4 cutter block on request. Changing the blades takes less than a minute per blade.

Jointing fence

The ball-bearing guided jointing fence runs smoothly and without tilting on tempered raceways – as precisely for many years to come as it does on the very first day. Chamfers can also be planed in a flash, because any angle between 90° and 45° can be set quickly with the user-friendly one hand operation. The integrated auxiliary fence which makes the processing of narrower workpieces considerably safer is worth mentioning.

Composite frame

The machine frame of the T54 is a sturdy and thick-walled composite structure whose design can only be found with this degree of technical perfection in MARTIN machines. Otto Martin invented this method of construction in the 1920s and had it registered as a design patent back then. Today, after more than 90 years of continual improvement, MARTIN still uses this simple and effective principle of frame construction. The intelligent combination of steel and concrete creates a high quality machine frame which is unparalleled when it comes to stability, absorbing capacity and torsion resistance. The vibrations which occur in any planer are absorbed many times more effectively than in cast-iron or even welded frames. This frame is the perfect basis for perfect work!
placeholder-img
Controls and Features

Xplane solid steel cutter block

The new 3-row Xplane cutter block from MARTIN impresses even when idling with remarkably smooth running. This impression is reinforced as soon as the block is engaged, as the block operates extremely quietly. Even the biggest depths of cut require a surprisingly low motor rating – another advantage. However, the surface quality which can be achieved with the Xplane, even on difficult woods, is really breathtaking.
  • Optimum health and safety by reducing the perceived noise exposure by 50%
  • The highest surface quality thanks to the further improved 3-row design
  • Minimised tear-outs due to shear cuts and the MARTIN XS cut of the blades
  • Low chip volumes and excellent chip flow thanks to an optimised layout
  • Reduced manual forces and high-grade surfaces thanks to MARTIN XS cut of the blades
  • Cost saving thanks to up to 20 times longer service life of the carbide blades as well as four cutting edges per blade
  • Cutter block speed 6,000 rpm, therefore optimum cutting speed

Control panel moving with jointing fence

This option moves the operating controls attached to the infeed table as standard above the table level. The depth of cut is digitally displayed and precisely set by turning knob. The hollow / pointed joint display is also very clear and easy to survey. That’s good for anyone who likes to have the most important thing in sight. If you move the jointing fence over the table, the control panel moves along with it and is therefore always within easy reach.

SUVAMATIC guard

The “SUVAMATIC” guard protects the entire planing area with a single cutter block guard. The folding infeed beak is very practical. This generates a slight contact pressure of the cutter block guard against the joining stop, depending on the setting. This promotes the joining quality considerably.

Auxiliary fence

The standard auxiliary fence is already integrated in the surfacing fence, in order to guide small, narrow workpieces safely over the machine table. This is an important contribution to improving health and safety.

TERSA solid steel cutter block with divided blades

If the rear section of the cutter block is equipped with 100 mm long carbide blades, edges of coated chipboards can also be joined tear-free. However, normal dressing and joining is possible in the front section of the block (410 mm). If the complete planing width is required, the blades are exchanged in seconds thanks to the TERSA principle. It goes without saying that other blade lengths and qualities can also be combined.

T45 and T54: Two singles – a perfect couple

You encounter two specialists which complement each other to perfection with the T54 surface planer and the T45 planer. Each of the machines is designed for its task without any compromises and provides optimum work results. The required machine is immediately available without time-consuming conversions and the two machines together take up hardly any more space than a combination machine thanks to the space-saving set-up. In contrast to a combination machine, both machines can also be operated in parallel without any restrictions – even by one person through optimum handling and the short distances.
Configure your individual T54
Model
Only with perfect surface planing results can you obtain the perfect end result. The T54 therefore offers ideal conditions for creating the optimum basis. Features such as the easy-running guided surfacing fence with integrated auxiliary fence, the electrical planing depth adjustment or the TERSA solid steel cutterblock Z2 stand out in this machine. The planing width is 500 mm.
T54 surface planer
Drive
Motor power 5.5 kW
Motor power 5.5 kW
Special voltage
Standard voltage supply 3 ~ / 400 volts - 50 Hz
Voltage supply 400 volts / 50 Hz
Special voltage: 3 ~ / 230 volts - 50 Hz
Special voltage 3 ~ / 230 volts - 50 Hz
Special voltage: 3 ~ / 210 - 240 volts - 60 Hz
Special voltage 3 ~ / 210 - 240 volts - 60 Hz
Special voltage: 3 ~ / 440 - 480 volts - 60 Hz
Special voltage 440 - 480 volts / 60 Hz
Safety guard
The height of the top part of the guard is adjusted parallel to the table.
CPS Prisma guard
The “SUVAMATIC" guard protects the entire planing area with a single cutter block guard. The folding infeed beak is very practical. This generates a slight contact pressure of the cutter block guard against the joining stop, depending on the setting. This promotes the joining quality considerably.
"Suvamatic” guard
Cutter block
The TERSA solid steel cutterblock with 2 blades is the standard equipment for the T54. The blade can be changed in a matter of seconds thanks to TERSA. Four blade qualities are available.
TERSA solid steel cutterblock Z2
The TERSA solid steel cutterblock with 4 blades provides the best surfaces especially when processing hard materials. A quick and easy change between Z4 and Z2 component parts is possible through the systematic use of dummy blades. The blade can be changed in a matter of seconds thanks to TERSA. Four blade qualities are available. The T45 planer is equipped with a 4-blade block as standard. This an option in the T54 surface planer.
TERSA solid steel cutterblock Z4
If the rear section of the cutter block is equipped with 100 mm long carbide blades, you can also join edges of coated chipboards tear-free. However, normal dressing and joining is possible in the front section of the block (410 mm). If you should require the complete planing width, the blades are exchanged in seconds thanks to the TERSA principle. The cutter block has two knife slots.
TERSA solid steel cutter block Z2 with divided blades
If the rear section of the cutter block is equipped with 100 mm long carbide blades, you can also join edges of coated chipboards tear-free. However, normal dressing and joining is possible in the front section of the block (410 mm). If you should require the complete planing width, the blades are exchanged in seconds thanks to the TERSA principle. The cutter block has four knife slots.
TERSA solid steel cutter block Z4 with divided blades
Traditional cutter block with 4 blades, incl. blade adjusting device, instead of the standard TERSA block.
Traditional cutter block Z4
The new 3-row Xplane cutter block from MARTIN impresses even when idling with remarkably smooth running. This impression is reinforced as soon as the block is engaged, as the block operates extremely quietly. Even the biggest depths of cut require a surprisingly low motor rating - another advantage. However, the surface quality which can be achieved with the Xplane, even on difficult woods, is really breathtaking.   • Premium surface quality thanks to improved 3-row construction • Reduction of tear-outs due to shear cuts and MARTIN XS (eXtra Sharp) knives • Increases safety standards by reducing the perceived noise exposure by almost 50% • Reduces costs due to 20 times higher durability and four cutting edges of the carbide cutters • Reduction of manual force and premium surface quality thanks to XS cut of the knives • Lowered chip volume (chips are broken up) and increased chip flow thanks to the unique tool geometry
Xplane solid steel cutter block with 3 spirally arranged rows of blades
Supplied in a set of 10.
Replacement screws for carbide blades, suitable for Xplane blocks
Supplied in a set of 10.
Cambered replacement carbide blades, suitable for Xplane blocks
1 pair of spare blades, HSS 18, suitable for traditional cutter block
Operation
This option moves the operating controls attached to the infeed table as standard above the table level. The depth of cut is digitally displayed and precisely set by turning knob. The hollow / pointed joint display is also very clear and easy to survey. That's good for anyone who likes to have the most important thing in sight. If you move the jointing fence on the table, the control panel moves along with it and is therefore always within easy reach.
Control panel moving with jointing fence
The switchable socket is used for operation of a feed on the machine, for example.
5-pin socket with plug
Machine table
The infeed table has been extended by 360 mm compared to the standard table and offers perfect support for processing long workpieces.
Infeed table 2,000 mm
The infeed table has been extended by 360 mm compared to the standard table and offers perfect support for processing long workpieces.
Outfeed table 1,580 mm
Miscellaneous
Not until you have a mastered machine to perfection can you exploit its maximum potential. Thorough on-site training by a MARTIN factory technician enables you to fully benefit from your machine.
On-site training / Commissioning
We offer tailored inspection and maintenance services for your MARTIN machines. You thereby maintain the operational readiness and accuracy of your machine over many years.
Inspection / maintenance by factory technician on site as per Martin maintenance schedule
For the use of the Configurator, please turn your device by 90°.
We will send you a non-binding offer
T54
Fields marked with * must be completed. We will, of course, treat your data as confidential.